Trampoline padding sizes we stock are: Reasons, why you may need to measure a trampoline, is for replacement parts or to see if the trampoline will fit in your garden comfortably.
Next, measure the mat itself, starting from one end of the fabric to the other, across the center.
How to measure a trampoline mat for replacement. To get the most accurate measurement, you should measure in 2 spots as shown in the diagram to the left. A round trampoline is a lot of fun but it is highly dependant on the jumping mat fitting correctly. Measure straight across to the opposite corner, to the outer metal edge of.
The most usual lengths are 5.5 inches or 7 inches. Measure your trampoline or bring your old mat into us. Verifying the size of round trampoline.
Round, rectangular, oval, and other shapes. It should lay vertically against the spring. That is why proper learning of how to measure a trampoline mat is needed.
In order to measure a trampoline, you need to make sure you have a tape measure, a pencil and notepad and a stepladder. Knowing how to measure your trampoline for the correct fitting mat will ensure your kids will still get lots of life out of heir existing trampoline. If your frame is 14ft, you need a 12ft , 12ft 3in, or 12ft 6in, depending on spring size.
Measure your frame measure across the diameter of the entire trampoline frame. See below where to measure from…. The different ways to measure the trampoline for the pads can be broken down in the shapes:
Measure your metal frame, count the number of springs, take 1 spring off and measure including the hooks. Outside to outside diameter of frame. If you have a round trampoline it is best to send or bring your mat into us to ensure your new mat is made to fit.
Note the diameter of the spring, or how wide the opening is. Take 4 individual measurements from a spring hole on one side of the trampoline frame to the spring hole on the opposite side of the trampoline. Extend the measuring tape to the other end of the opening.
The size of an octagonal trampoline is measured by the diameter of the metal frame (not the jumping surface) from corner to corner (not side to side). If you’re measuring a round trampoline, visualize it as a clock. We have a trampoline replacement mat calculator (only suitable for round trampolines), that will take the stress out of ordering and give you confidence that the trampoline mat you order will fit your trampoline (accurate measuring is required).
Because with the wrong measurement, chances are you’ll end up buying wrong sized springs or frames. For round mats (jumping surface): Measure the outside diameter of the spring.
The average of these two measurements is your. If you are ordering a new trampoline mat, it may be wise to order a few springs at the same time. Find your trampoline’s diameter in feet by measuring across the steel frame from outer edge to the opposite outer edge.
If you need assistance please call us on (03) 5292 1100 or message us here. Mat has to be on the trampoline; To avoid this you should be careful enough when measuring a trampoline mat.
Place the ruler or measuring tape against the opening on the spring, next to one of the hooks. Here are instructions on how to measure for a round replacement trampoline mat. Measure the trampoline diameter in 2 spots with the mat still fully assembled and uses the “average” as your “actual” trampoline size.
These measurements are your frame’s. To correctly measure the jump mat, you need to measure the frame size of your trampoline. In order to get you the correct mat, you will need to know:
This is the typical stated measurement (i.e.: Find your trampoline’s diameter by measuring from one side of your frame’s outer edge to the opposite outer edge. Mats are sold by actual size of mat material.
The trampoline diameter is measured from the outside of the metal frame to the outside of the metal frame (not the jumping surface) see image below. Either tip of triangle, or inner edge of mat hole (even if hole is torn. Almost always, you can round to the nearest foot.
A trampoline mat replacement is a crucial update that your trampoline needs when they become worn or torn. To find the diameter of your octagonal trampoline, start at the outer metal edge of the trampoline, at one of the corners. Follow the instructions above to measure the frame of a round trampoline.
(count the holes in the frame where the springs attach.) d: This guide will help you correctly measure your trampoline mat and ensure that you purchase the correct replacement mat for your best american trampoline. Measure length and width in centimetres;
How to measure the mat on a round trampoline. You also need to measure the spring size of your springs from hook to hook ensuring it is not stretched. 8, 10, 12, 13 and 14 foot.
You will measure across the middle of the trampoline from outside frame to outside frame, straight across the middle. Measuring the trampoline mat correctly is important. The round 12’ replacement trampoline mat by partysaving costs approximately $50, is 12’ in diameter, and is designed to be used with trampoline frames that are 14’ in diameter.
The measurements for a replacement trampoline pad will depend on the shape of the trampoline, just like it was with the mat. The usual measurements for a trampoline mat are 12ft., 14ft., and 15ft. Measure twice in a cross formation to ensure that the mat is indeed a perfect circle.
The average of these two measurements is your trampoline frame's approximate size. Do not measure the inner ring of the trampoline mat itself. How to measure for a round trampoline mat.
You will take a spring off of the. When ordering a trampoline mat replacement, make sure it is the correct mat to fit your trampoline properly. If you need to replace the mat on a round trampoline, measure the outside diameter of the trampoline’s frame.